TRENDnet Printer TEW MP1U User Manual

Quick Installation Guide  
TEW-MP1U  
 
1. Before You Start  
Package Contents  
?TEW-MP1U  
?Quick Installation Guide  
?Utility CD-ROM  
?Power Adapter (12V, 1A)  
System Requirements  
?CD-ROM Drive  
?CPU: 300Mhz or above/ 800Mhz or above (Windows Vista)  
?Memory: 256MB RAM or above/ 512MB RAM or above (Window Vista)  
?Windows 2000/XP/2003 Server/Vista (32bit)  
Note:  
1. Do not perform the following unless instructed to do so:  
1. Install the utility  
2. Connect printer to printer server  
3. Connect computer to Print Server  
2. The utility must be installed on each computer in order to use your multi-  
function printer.  
Application  
1-Port Wireless G Multi-Function  
USB Print Server  
(TEW-MP1U)  
Multi-Functional  
USB 2.0 Printer  
Workstation with  
Wireless G PCI Adapter  
(TEW-423PI)  
Internet  
Notebook with  
Wireless G PC Card  
(TEW-421PC)  
Wireless G  
Firewall Router  
(TEW-432BRP)  
Cable/DSL Modem  
1
 
English  
2. How to install  
1. Install the printer drivers to your  
computer. Then shutdown the  
printer and disconnect the printer  
from your computer.  
Note: Please refer to your printer's manual for printer installation instructions.  
2. Connect the Power Adapter to  
the Print Server and then to a  
power outlet.  
3. Connect a RJ-45 network cable  
from a Switch/Router to the LAN  
port of the Print Server.  
4. Connect the USB Printer to the  
USB port of the Print Server.  
5. Power ON printer.  
6. Verify that the Status LED is lit on  
the Print Server.  
2
 
English  
3. Configure the Print Server  
1. Insert the Utility CD-ROM into your  
CD-ROM driver. Then click Setup  
Wizard.  
2. Click Skip.  
3. Select the print server and then  
click Next.  
3
 
English  
4. Choose a wireless network to  
connect to and then click Next.  
5. Configure the IP address of the  
print server to be in the same  
subnet as your network and then  
click Next.  
6. Click Finish.  
4
 
English  
7. Click Yes.  
8. Follow the InstallShield Wizard  
instructions and then click Finish.  
9. Click on Resource and then click  
Connect.  
10. The printer driver wizard appears.  
Follow the printer driver wizard to  
install the printer.  
5
 
English  
11. Click OK.  
Print Server configuration is now complete.  
For detailed information regarding the TEW-MP1U configuration and advanced  
settings, please refer to the User's Guide on the Utility CD-ROM or  
Register Your Product  
To ensure the highest level of customer service and support, please take a moment to  
register your product Online at: www.TRENDnet.com/register  
Thank you for choosing TRENDnet  
6
 
English  
4. Printing  
Note: Only one user can use the print server at a time. Once a user has  
finished using the print server, another user can use it.  
1. Click on Resource and then click  
Connect.  
2. Status will now show the client  
computer and IP address that is  
currently using the printer.  
3. User can now start printing.  
4. Click Disconnect.  
7
 
English  
5. Faxing  
Note: Only one user can use the print server at a time. Once a user has  
finished using the print server, another user can use it.  
1. Click on Resource and then click  
Connect.  
2. Status will now show the client  
computer and IP address that is  
currently using the printer.  
3. User can now start Faxing. Follow  
the Multifunction printer software  
instructions for faxing.  
4. Click Disconnect.  
8
 
English  
6. Scanning  
Note: Only one user can use the print server at a time. Once a user has  
finished using the print server, another user can use it.  
1. Click on Resource and then click  
Connect.  
2. Status will now show the client  
computer and IP address that is  
currently using the printer.  
3. Place the document on the Multi-  
Function Printer's Scanner bed.  
Then follow the Multifunction  
printer software instructions for  
scanning.  
4. Click Disconnect.  
9
 
English  
Troubleshooting  
Q1. The setup wizard/utility does not detect the Print Server and/or printer/storage device. What  
should I do?  
A1. First, double check your hardware connections; make sure that the Print Server and printer are  
powered ON and are properly connected. Make sure the RJ-45 network cable is securely connected to  
the Print Server and Switch/Router. Second, disable any software firewall programs such as ZoneAlarm  
or Norton Internet Security. If your computer is running Windows XP or Vista, disable the built-in firewall.  
Third, click Refresh. Fourth, power cycle the Print Server. Unplug the power to the Print Server, wait 15  
seconds, then plug the Print Server back in.  
Q2. The setup wizard/utility does not detect my printer device. What should I do?  
A2. First, make sure the printer is powered on and properly connected to the Print Server. Second,  
connect the printer with another USB cable. Third, reset the print server. Take a pin or paperclip and  
press the reset button on the print server for 15 seconds, then let go.  
Q3. I am unable to print to my print server. What should I do?  
A3. First, make sure you follow the exact steps for installing the Print Server in section 2 Second, make  
sure to right click on the print server in the utility and click connect. If another user is using the print  
server, you must wait until the user is finished using it. Third, if you are connected to the print server and  
are idled for a couple of minutes, a warning message appears. If you do not respond within a minute, you  
will be automatically disconnected from the print server. You must connect to the print server again.  
Q4. I can print a test page, but I cannot print anything from Microsoft Word or other applications.  
A4. Make sure to set the newly installed network printer as your default printer. Click Start  
and then click Printers & Faxes, verify that your printer icon has a check on it.  
Q5. I configured my print server to automatically receive an IP Address from a DHCP server, and now I  
cannot go into the print server’s web utility.  
A5. Open the Print Server Set Up Wizard (See 3. Configure the Print Server) to locate  
your print server’s IP Address.  
Q6. Is there a way to force a computer to give up ownership of the print server?  
A6. If the user has been idled for a few minutes, the user will be automatically disconnected.  
Q7. After I successfully configured the TEW-MP1U to match my wireless network settings, I can not print  
through the Print Server.  
A7. First, verify that the wireless settings match your wireless network settings. Second, after configuring  
your wireless network settings, make sure to unplug the power to the Print Server, disconnect the Ethernet  
cable from the Print Server, wait 15 seconds, then plug the Print Server back in. Third, verify that the  
WLAN LED on the Print Server is lit. Fourth, if you have enabled encryption on your wireless network,  
find out the type of encryption (e.g. WEP, WPA-PSK) and encryption key. Then open up the setup wizard,  
connect to the desired wireless network and enter the encryption key.  
If you still encounter problems or have any questions regarding the TEW-MP1U, please refer to the User's Guide  
included on the Utility CD-ROM or contact TRENDnet's Technical Support Department.  
10  
 
Certifications  
This equipment has been tested and found to comply with FCC and CE Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference.  
(2) This device must accept any interference received. Including interference that may  
cause undesired operation.  
Waste electrical and electronic products must not  
be disposed of with household waste. Please  
recycle where facilities exist. Check with you Local  
Authority or Retailer for recycling advice.  
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV  
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS  
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO  
OPERATE THE EQUIPMENT.  
ADVERTENCIA  
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón  
necesario para su funcionamiento. El uso de un adaptador distinto al mencionado puede producir  
daños fisicos y/o daños al equipo conectado. El adaptador de alimentación debe operar con voltaje y  
frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalación.  
 
TRENDnet Technical Support  
.
US Canada  
Toll Free Telephone: 1(866) 845-3673  
24/7 Tech Support  
.
.
.
.
Europe (Germany France Italy Spain Switzerland UK)  
Toll Free Telephone: +00800 60 76 76 67  
English/Espanol - 24/7  
Francais/Deutsch - 11am-8pm, Monday - Friday MET  
Worldwide  
Telephone: +(31) (0) 20 504 05 35  
English/Espanol - 24/7  
Francais/Deutsch - 11am-8pm, Monday - Friday MET  
Product Warranty Registration  
Please take a moment to register your product online.  
20675 Manhattan Place  
Torrance, CA 90501  
USA  
 
Copyright ©2007. All Rights Reserved. TRENDnet.  

Tektronix Sander TDS 600C TDS 700D User Manual
Tiger Products Co Ltd Lawn Mower RBF 12C User Manual
Toshiba Network Card MK1504GAL User Manual
TV Ears Clothes Dryer DRI DOCK User Manual
Uniden Marine Radio MC2700 User Manual
Uniflame Outdoor Fireplace WAD792SP User Manual
Unisar Baby Monitor TV984 User Manual
Vivotek Network Card PZ6112 User Manual
WatchGuard Technologies Washer XTM 5 Series User Manual
Weber Gas Grill 55545 User Manual